what is the difference between rj45 and rj48? - Cisco Community
2002年6月28日 · In simple terms: RJ45/RJ48 has their own "pinout" used to wire the modular plugs. RJ45/RJ48 uses 8 pins & 8 connectors - Yet not compatible. (why it matters) The difference is: RJ48 is designed for STP (Shielded Twisted Pair) Cable (thicker) RJ45 is designed for UTP (Unshielded Twisted Pair) Cable (thinner) Why it matters:
Solved: RJ48 or RJ45 Help for PRI - Cisco Community
2008年5月25日 · In fact, original cisco PRI cables have no key. So you're OK with regular RJ45 connectors to make a custom made cable. If possible, use proper 100 Ohm T1 cable, especially if the patch is longish. 0 Helpful. Reply. Solved: I've read that while an RJ45 will work, an RJ48C should be used for a PRI coming from smart jack into a Cisco vwic.
RJ48C vs RJ45 - Cisco Community
2002年6月13日 · From an RJ48 jack, terminate 1 2 and 5 6, then if the CSU is internal, connect the cat 5 straight through to the DTE. The cross is done on the jack. 06-18-2002 06:03 AM. The pinout for a T1 is as follows: Pins 1&2 are used for your …
Difference between WS-X4548-RJ45V+ and WS-X4548-GB-RJ45V
2011年2月10日 · Capable of up to 30W of inline power per port. Enterprise and commercial: designed to power next-generation IP phones, wireless base stations, video cameras, and other PoE devices that require. power up to 30 watts. WS-X4548-GB-RJ45V Cisco Catalyst 4500 PoE IEEE 802.3af 10/100/1000, 48 Ports (RJ-45) WS-X4548-GB-RJ45V:
topic what is the difference between rj45 and rj48? in Other …
In simple terms: RJ45/RJ48 has their own "pinout" used to wire the modular plugs. RJ45/RJ48 uses 8 pins & 8 connectors - Yet not compatible. (why it matters) The difference is: RJ48 is designed for STP (Shielded Twisted Pair) Cable (thicker) RJ45 is designed for UTP (Unshielded Twisted Pair) Cable (thinner) Why it matters:
NM-2CE1T1-PRI Pinout Configuration - Cisco Community
2006年6月26日 · NM-2CE1T1-PRI Pinout Configuration. 06-25-2006 11:38 PM - edited 03-03-2019 01:07 PM. Dear Collegue, I have NM-2CE1T1-PRI module card newly installed in our 3660 routers in some of the sites. I tried to figure out, what type of interface I will use if the service provider will provide me a couple of E1's to connect to the other sites.
Auto-Mdix on WAN serial port - Cisco Community
2020年7月2日 · it all depends from the ISDN / WAN provider NT network termination is that device that might be able to perform the E1/T1 crossover allowing you to use a straight RJ45 cable. However, there are cases where the NT devices expects to receive two BNC cables for G.703 in that case you would need a cable converter.
What are the diffrences between the WS-X4424-GB-RJ45 and the …
01-24-2005 10:36 AM. To begin with, WS-X4424-GB-RJ45 has 24 ports and 4:1 oversubscribed while WS-X4548-GB-RJ45 has 48 ports and 8:1 oversubscribed. If you meant to say difference between WS-X4548-GB-RJ45 and WS-X4448-GB-RJ45, the 4548 is. • Time domain reflectometer (TDR) capable with TDR support in a future software release.
cab-e1-rj45bnc(unbalanced), output rj45 or rj48?
11-26-2012 06:28 PM. Yeah, I think I got you, rj45 and rj48 are in fact the same kind of connecter, and this cable"cab-e1-rj45bnc (unbalanced)" is just a cable used to transfer bnc signal to rj45, it has nothing to do with E1 or Ethernet, if there is E1 signal ,the rj45 of the cable can be inserted into E1 port, if there is Ethernet signal, the ...
What is difference between Serial and Ethernet - Cisco Community
2017年3月2日 · Hi, In addition to below links, small crisp definition for your reference. Serial interfaces are used by ISP to provide WAN connections as a frame relay, T1, T3, etc. The port used is V.35 or RS232. Ethernet interfaces are used …