ceiling board | Drywall Talk - Professional Drywall and Finishing ...
2009年9月14日 · We use 1/2" cd ( ceiling board) or 5/8" depending on specs for lids 24" oc. Regular 1/2" on main floors with 16" oc joists and no insulation load. Save Share Reply Quote Like
Electric Heat Sheetrock | Drywall Talk - Professional Drywall and ...
2010年2月13日 · each room. It also was a very even heat. We had a separate price for the ceiling board since it did take more time. Back then a normal house was all 1/2" thick 12' length board. There wasn't 6 different types and lengths of board in a house. The average house was a FHA house with 90 or so sheets. Everything was 8' and nothing wrapped.
Wood strapping or furring versus resilient channel
2011年4月21日 · Based on previous posts, the "ceiling board" is stiffened to work on 24"OC. JoePro recommends using 5/8ths instead of the ceiling board. So here are some comparisons I've got so far: I'd assume the ceiling board is lighter to handle than 5/8ths. Costs: 4x12, 1/2" regular: $17.24 (so for 1000sq ft = $362)
5/8 " Drywall on Ceilings | Drywall Talk - Professional Drywall and ...
2013年2月10日 · As far as length I've seen a lot of 1-1/4" used, common would be 1-5/8" coarse thread. Forget the fine thread they take to long to drive in, this is over wood. The best would be check the building code in your area for specifications on applications for wallboard. aka the rock doctor. Reply Like.
Best drywall for garage ceiling? | Drywall Talk - Professional …
2012年1月3日 · i complete every garage.2 of the builders i work for sheet walls with half inch plywood,drywall ceiling,i tape in drywall ,mesh in plywood ,coater up sheetrock90,splatter coat finish.gas seal required anyway ,so they want them finished for paint
Installing T-Bar Ceilings | Drywall Talk - Professional Drywall and ...
2015年9月11日 · The ceiling was two levels, Optima 6"lower than a Woodworks 1x4 in black grid. The transitional bulkhead was semi eliptical. Floor was slopped, architect wanted 18g steel to deck 4'above. Ended up building the drop with 25g track and drywall, no studs at all, just the wires and struts every 12 along the curve.
butt boards backblocking butt joints - Drywall Talk
2014年2月15日 · But the next joint it popped the screws like mad when I went to apply the second sheet. We are using ultra light board here and it is a lot less dense. It appears to be very crispy. Many times when it pops a screw it takes chunk of board with it. So I am pretty sure the butt boards are not going to work for me with the ultra light board.
Gaps between old ceiling and new walls - Drywall Talk
2023年9月23日 · Next stop on the DIY adventure, taping the old ceiling to the new walls and best advice on fixing this huge chunk that came out. I tried as best as I could to get the new drywall up and behind the ceiling boards (3/8" boards). In some places, the ceiling is just coming up short of the wall by a good 3/4" at worst.
Joist direction change | Drywall Talk - Professional Drywall and ...
2022年3月22日 · Tonydif. 62 posts · Joined 2021. #6 · Mar 25, 2022. When ceiling joists change direction, layout is incredibly important. Map the ceiling so board will not have to change direction. Run bevel to bevel throughout. Start layout at the beams, keep the beams as close to middle of sheet as possible, while assuring beveled edges land on joists.
Hanging ceiling when walls are already up - Drywall Talk
2019年12月8日 · Create boxes constructed from wood framing and drywall and install the ceiling drywall around these items, or create your own suspended ceiling with a new, framed ceiling. Secure 2-by-6-inch boards to the walls studs all around the room slightly below the utility lines, creating new ledger boards.