Mixing ABS and PVC Drain Fittings - InterNACHI®️ Forum
2012年3月31日 · For example, solvent cementing is prohibited between ABS and PVC, PVC and chlorinate polyvinyl chloride (CPVC) or ABS and CPVC. Saddle-type fittings may be moved out of alignment, can weaken the pipe because of the pipe wall penetration and typically do not form a drainage pattern connection.
PVC & ABS pipe - Plumbing Inspections - InterNACHI®️ Forum
2006年11月16日 · mlarson (Michael Larson, WI Lic. # 1672-106) November 16, 2006, 6:54am 4. jpope: ABS and PVC cannot be directly glued together. A special ABS to PVC transition cement (available at HD) exists and may be used with conditions in non pressurized piping and the as always with the approval of the local AHJ. It is not intended to be used at multiple ...
Used PVC glue on ABS pipe, now what? - Fine Homebuilding
2020年5月22日 · Test 1: I cut a piece of 2" ABS pipe in two and then used the PVC glue to attempt to glue it back together. Test 2: I glued to pieces of ABS pipe together (side by side) While neither of these tests reflects a plumbing fitting, I think the tests should expose if a weld actually takes place on the ABS material.
Gluing ABS and PVC DWV - Fine Homebuilding
2003年5月23日 · It says for ABS and PVC, doesn't say anything about not using it to glue the two together so what the heck, I tried it. It's still drying. After 15 minutes there was still some give in the joint if you applied a fair amount of force. Unlike PVC which has practically zero give after just a …
Joining ABS DWV to PVC Reliably - Fine Homebuilding
2004年1月28日 · Joining ABS DWV to PVC Reliably. You can use a no-hub coupling–the rubber sleeve with 2 hose clamps. These come in slight variations depending on the materials they are intended to join, so make sure to get the right one. No-hubs are an accepted leakproof way of joining pipe–cast iron pipe is routinely assembled with them.
Joining ABS with PVC - Fine Homebuilding
2006年7月2日 · PVC glue will in most cases will glue abs/abs & abs/pvc. But I have yet to see a jurisdiction that allows this practice. A transition coupling is required in every jurisdiction that I have worked in. I wouldn't worry about the glued joint failing over time. AndyCharron1 | Jul 03, 2006 02:37am | #7.
Prep and Glue Plastic Fittings - Fine Homebuilding
9. Glue both sides. Apply two coats of glue to the male side and a single, light coat to the female side of the connection. Push the parts together with a quarter turn, and hold for 15 seconds while the glue sets.
Bonding HDPE drain pipe to PVC fittings - Fine Homebuilding
2011年4月10日 · My understanding is that HDPE is resistant to most solvents and won't solvent-weld very well. Of course, the two-tone stuff may have the outer layer made of something else that's more easily joined -- I think someone needs to dig into the specs for the stuff. It's possible to put a pvc coating onto the hdpe.
ABS repair - Fine Homebuilding
davidmeiland | Jul 28, 2005 12:21am | #24. Normally I would expect 1-1/4 or 1-1/2 traps under sinks to be pvc or chrome, screw-together compression stuff that can be taken apart and cleaned. Plumbing in the wall would be ABS, with a trap adapter glued into the tee. Basically, none of the trim out parts glued.
Dry fitting ABS - Fine Homebuilding
moltenmetal | Aug 25, 2006 03:48pm | #7. Use Vaseline with extreme care: you need to remove ALL OF IT if you're going to make a leak-tight joint long-term. ABS usually isn't supplied with a cleaner/primer, but if you're using Vaseline beforehand you will definitely need to clean/prime the joint before you glue it.