Cleaning Rust Out Of A Gas Tank With VINEGAR - DO THE TON
2011年12月25日 · First buy a large box of 1" long sheetrock screws, $20.00. Then buy 4 gal's of white vinegar from the grocery store, $10.00. Then simply insert all the sheetrock screws into the tank, close the cap and shake the hell out of it by hand. I shook it on and off for a day. Every time I walked past it I would shake it.
Doesn't Simple Green remove rust? - DO THE TON
2011年8月6日 · No, it doesn't. Simple Green is nothing but soap. Its very concentrated soap, but its just a liquid soap, mixed with a little acidic water. The truth is the stuff is no better than liquid dish soap and a stiff brush. People love it though, why is beyond me. I guess its a lot like WD-40, a product that has no earthly use, but people swear by it.
Gas tank won't stay clean! How can I stop flash rust?
May 5, 2014. #3. Diesel or automatic transmission fluid. Pour a bit in, slosh it around, drain the excess. You can use it on the outside as well, apply with a rag. When you are ready to paint, wash the tank with acetone or cheap lacquer thinner until you get zero residue on a clean white cotton rag (cloth diaper is best, shows the slightest ...
Removing surface rust on fork tubes - DO THE TON
Feb 23, 2010. #3. as i recall the fork tubes are "hard chrome". if you see rust, the chrome is non-existent beneath it. you can clean it off (scotch brite, fine steel wool, tin foil) but it more than likely will come back. im going to try painting mine, as cleaning only lasted about 6 weeks before i could see the rust again (im close to the ...
Rust removal project. Advice needed | DO THE TON
2013年8月27日 · Wasnt sure where to post this so i admit to posting it twice i will remove one if a mod has a prpblem with ...
Removing surface rust from cylinders - DO THE TON
2014年1月30日 · Feb 2, 2014. #7. The best and easiest way to remove the rust (not the pitting) is aluminum foil. Just take a small piece of foil fold it into quarters wet it and start rubbing. It sounds strange but it works great with minimal effort. The foil is softer then the metal you are cleaning so no chance of marring the surface.
Cleaning the rust from that old tank - DO THE TON
2008年6月21日 · Remove your petcocks and any other lines, pour the Zep out and wash out with lots of water. Wash your petcocks too. Save the Zep for the next tank. Wash the remaining water out of your tank with some alcohol, or something like that. Let it dry, or fill it with gas and go.
Can't Remove cb350 Swingarm - DO THE TON
2013年1月18日 · These Castle nuts allow way too much moisture in the small slits. Rust starts and locks them up. Me, if I did not have an impact wrench and compressor, or a 30 inch 1/2 inch drive breaking bar, I would get a cold chisel and split the nut, 2 sides, 30 degrees apart will allow it to be popped off in minutes. Just playing the ideas around now.
Reusing Evapo-rust "update, review" - DO THE TON
Over 1,000 Posts. Aug 6, 2010. #2. Re: Reusing Evapo-rust Yes you can, perfectly ok. I use the POR-15 version of it and they actually recommend you reuse it. C.
BEST WAY TO STRIP PAINT OFF OF FIBERGLASS - DO THE TON
Aug 7, 2013. #10. Wet sand it with 220. Takes paint right off, and doesn't leave deep scratches in the gel. When you get the paint off, block it down to 800 or 1,000 to get it ready to paint again. And, block sand it, so you don't create dips in the gel. I use durablocks. P.