Where to buy PVA glue - Forum - DakkaDakka
2012年3月18日 · Subject: Where to buy PVA glue. spacewolf407. ... Okay, so I've been to Michaels, Joann, Home Depot, and ...
Glue and You - Articles - DakkaDakka
It's not really irritating to your skin, in my experience,but getting the uncured glue on yourself is very annoying and will leave tacky spots for a day or two until it wears of. Obviously if you get some uncured glue on your model, it's nigh-impossible to remove. So be careful. Where you can get it: Home stores, such as Lowe's, Home Depot, Amazon.
Glue for Basing - Forum - DakkaDakka
2012年10月30日 · OP: you might have used too much glue, and not enough sand. you really need to coat the glue in the basing material, not sprinkle it. if its a problem, you CAN pre mix the glue and sand, just add more glue and apply that way. a crappy paintbrush is a good thing here. if you don't like them, just remove it and try again. should pull right off.
Simple Mud and Grass - Basing Tutorial - Forum - DakkaDakka
2011年1月13日 · Step 2 - Sand & Glue (a) - Place a a decent blob of PVA glue on your chosen base, enough to cover and not be too thin when spread out. (b) & (c) - Spread the PVA out to the edges of the base with an old paintbrush, taking care not to spill glue over the edges. (d) - Dunk the base into your sand/gravel mixture.
Muddy puddles - water without water effect? Now with guest …
2019年2月24日 · So I 'd say doing waves of lava by putting several layers of PVA glue on top of each other might work. I don't think it will look very voluminous, though, as the glue will only hold its shape up to a certain height before its own weight spreads it out further than you want. I don't think painting over PVA glue should be a problem if you use primer.
how to get rid of pva glued base? - Forum - DakkaDakka
2010年9月17日 · PVA should loosen up with water. I toss my bases with flock or sand into a bowl of water overnight and then rinse the stuff off before dropping them in Simple Green to strip the paint. I do 10 or 20 bases at a time, I am slowly rebasing a few old armies from green and flocked to brown with sand.
Basic's about using glue | Warhammer 40K - Forum - DakkaDakka
2009年1月16日 · Glue: You will use four main types in modelling. 1: Super glue, which is good for gluing everthing, but bad because you need to be ventilated and it will eventually stick you to something. Melts plastics including unpressed Styrene. Dries clear. 2: Plastic Cement, which sticks plastic to plastic , but nothing else. Dries clear.
PVA glue as liquid modeling putty? - Forum - DakkaDakka
2012年2月5日 · PVA and green stuff are made from different compounds. If you check the MSDS of these products, you will see. The PVA turning white and then clear, is most likely caused by the water dissolving some of the glue. As for reasons, I can't think of any at this stage.
How to glue sand to plastic? - Forum - DakkaDakka
2015年1月20日 · Straight PVA to apply it to the area, and then mix PVA and water about 1:3 and paint that mixture over the sand after it has dried to the area. This will make it pretty much impenetrable once the water/PVA mix dries over the top, but it will still paint well, especially if you use primer first. So: 1. PVA for the sand 2. Let dry 3.
Basing Miniatures - Forum - DakkaDakka
2011年11月22日 · PVA=White Glue=Elmers. Its all pretty much the same stuff. For sand, grass/flocking, cork, etc this is the stuff to use. If your glueing a plastic cover piece (like the tile sheet from plastruc) over an entire base then go with a model airplane glue to chemically weld the plastic sheet to the base.