Atlas Lathe Manuals | The Hobby-Machinist
2015年10月30日 · Shaper - Metal - Plans 2. Peerless ... Atlas Lathe 06 10200 MK2 Metric CI Roller Rev 3.pdf. 0.00 star(s) 0 ...
General Discussions of Atlas Lathes | The Hobby-Machinist
2015年1月25日 · The upside of the Atlas is low cost and lots of spare parts. The Downside of the Atlas are the Zamak (zinc alloy) gears, soft flat bed ways, and lack of mass/rigidity. My favorite of the low cost machines was the Logan 820. That said, zillions of good quality turned products have been produced on Atlas lathes.
Atlas/Craftsman 6" Metal Lathe restoration 101.07300 1937
2021年1月23日 · 48. Jan 22, 2021. #1. I have started a restoration on a 1937 Craftsman 101-07300 6" metal lathe. The lathe is being restored for a friend whose Grandfather purchased the lathe new in 1937. The lathe was then passed on to my friend's father. At some point, the lathe fell into disuse and has been rusting away in a damp basement since her father ...
Atlas 618 Metal Lathe - The Patriot Woodworker
2013年7月29日 · Posted October 26, 2022. We recently moved my dad into assisted living and are trying to sell some of his "work area" items. One is an Atlas metal lathe, model #618, serial #019620. I'm trying to find out how much it's worth, but am having a hard time finding this particular model online.
Atlas/Craftsman 101.07382 12" lathe with Timken bearings question
2018年12月9日 · All of the Atlas-Craftsman 12" lathes with Model Numbers between 101.07360 and 101.07383 originally came with babbit bearing headstocks. So the headstock is probably newer than the rest of the lathe. The 101.07382 was in production for only only about one year, 1938. And if the headstock has a rectangular instead of oval escutcheon for mounting ...
Atlas metal lathe | The Hobby-Machinist
2022年3月31日 · Those are often accurate to a few tenths. Put it in the chuck and use an indicator while spinning the chuck by hand. If it runs true, you know it was the material. If not, the chuck, backplate, spindle, or bearings could be having an issue. If it is the stock, take a cut and it will become straight.
Back Gear Operation Atlas 10f - The Hobby-Machinist
2015年1月25日 · I have a Craftsman (Atlas) 6" lathe and there is a pin mounted in the forward gear that engages the pulley for direct drive. For low speed, loosen the set screw and pull the pin out enough to permit the gear and spindle to rotate freely. To engage the back gears then rotate them into the spindle gears.
Possible first lathe: Atlas TV48 | The Hobby-Machinist
2014年8月24日 · The Atlas model TV48 is one of four lengths of F-Series 10" machines built. "T" means that it has Timken spindle bearings, which is good. "V" means that it has a vertical countershaft. The 10F are 16-speed machines. The spindle and countershaft each have 4 …
A lathe finally! Craftsman 12x36 101.27440 - The Hobby-Machinist
2012年1月31日 · Jeff, Harris makes low temperature solders (400F) and their "Stay-Clean" fluxes. Soldering Diecast is a little tricky though because the melting point of the solder is close to the melting point of the zinc diecast. If you are good with a torch it'll work fine, otherwise you may want to explore other options. Tom.
Indexing pin on Atlas/Craftsman 12" lathe - The Hobby-Machinist
Aug 26, 2011. #2. Which version of the lathe do you have? Originally on most of the 10/12" Craftsman/Atlas lathes, the indexing pin was held in place with a spring and ball. If you look inside the hole for the pin you should see a small hole that would hold a 3/16 diameter spring (maybe smaller) and the ball just sits on top of the spring.