microhardness

  • 网络显微硬度；微型硬度；微硬度分析

网络释义

1.
显微硬度
冶金词汇英语翻译(H-N) ... micrography 显微检验 microhardness 显微硬度 microhardness tester 显微硬度计 ...
www.zftrans.com|基于90个网页
2.
微型硬度
努普显微硬度试... ... 1) 硬度; hardness 5) 微型硬度; microhardness 6) 最小点燃电流比; minimum ignition current ratio;MICR ...
www.chemyq.com|基于3个网页
3.
微硬度分析
2-5-1微硬度分析(microhardness) 19 2-5-2 偏光法(polarizing microscope) 19 2-5-3 X光微显影技术(x-ray microradiography) 21 …
cetd.tmu.edu.tw|基于2个网页
4.
显微维氏硬度计
渗层有硬度，须用显微维氏硬度计(microhardness)检测表面硬度。HV500左右(Layer Thickness less than 2mm)ztljlljtk 2006-10 …
www.mechcad.eu|基于2个网页
5.
压痕硬度值
...间后卸除试验力，用测量的压痕对角线长度 计算的一种压痕硬度值 (microhardness) 显微硬度主要用于确定很薄的材料、细金 …
www.docin.com|基于 1 个网页

例句

释义:
全部全部,显微硬度显微硬度,微型硬度微型硬度,微硬度分析微硬度分析
类别:全部全部,口语口语,书面语书面语,标题标题,技术技术
来源:全部全部,字典字典,网络网络
难度:全部全部,简单简单,中等中等,难难
1.
The annealing temperature has significant effect on microhardness of AZ31, however, the time of annealing has no effect.
退火处理温度对AZ31镁合金的硬度值有显著影响，但退火处理时间的影响却不明显。
www.showxiu.com
2.
The high frequency induction hardening can't raise the surface microhardness of the cold precision forging spur gear.
高频感应淬火不能达到硬化冷精锻直齿圆柱齿轮齿面的目的。
www.juhe8.com
3.
After ultrasonic impact, the surface microhardness and the section microhardness are obviously increased.
冲击后接头的表面和断面显微硬度均得到了提高。
www.yhclgy.com
4.
The microhardness distribution of the welded joint is along the welding line. The microhardness is higher in nugget zone, and lowest in HAZ.
焊接接头的硬度分布沿焊缝中心基本对称，焊核区硬度较高，热影响区硬度最低。
rjggy.net
5.
The microhardness is higher and grain size is smaller in weld bead zone, compared with the heat-affected zone and base metal.
相对母材和热影响区，焊缝的晶粒明显细小，显微硬度比热影响区和母材稍高。
rjggy.net
6.
The microhardness of the cladding layer was measured by microhardness tester, and its microstructure was observed by SEM.
利用维氏硬度计测试了其显微硬度，用扫描电镜分析了激光熔覆层的微观形貌。
rjggy.net
7.
The deposition rate, microhardness, corrosion rate of low temperature iron plating layer at different temperatures are investigated.
研究了在不同温度下获得的低温镀铁层的沉积速率、显微硬度、腐蚀速率等性能。
www.ceps.com.tw
8.
The result showed that the microhardness, finish and time of strengthening layers related to parameter of strengthening technology.
试验结果表明，表面强化层硬度、表面光洁度和强化时间与选择工艺参数有关；
www.chemyq.com
9.
The hardening layer was analyzed by metalloscope, microhardness, electronic probe and transmission electron microscopy.
用金相显微镜、显微硬度计、电子探针和透射电镜对硬化层进行分析。
rjggy.net
10.
The deforming principle of fine blanking is analyzed from streamlines microstructure and microhardness of the testing part.
通过试件流线、金相组织以及显微硬度等方面对精冲变形的机理进行了分析和研究。
dictsearch.appspot.com